Rivera-primo Brute IV 2" Touring Bedienungsanleitung PDF herunterladen

NOTE: Read the instructions carefully before proceeding with the actual installation.

NOTE: To avoid accidental start up of vehicle during the installation, remove both battery

cables & the battery. Securely block motorcycle in an upright position. Different models will

require the removal of shifting levers, foot pegs, etc. Remove whatever is necessary to

accomplish the installation per your OE service manual.

Using your OE manual, strip the motorcycle down to

what is shown in Figure 1.

Remove the bearing race from the transmission main-

shaft using JIM’Sl part # 34902-84.

Remove alternator rotor and check sprocket shaft oil

seal. The steel back on this seal should face away from

the engine when using a primary belt drive which will

keep oil from leaking into belt drive.

(Use seal HD part # 12068).

NOTE: All fasteners should be treated with a small

amount of either blue or red threadlocker depending on

the application.

Apply 2 drops of blue threadlocker on all motorplate

bolts. (See Figure 2)

Apply blue threadlocker to & then install

the 4 bolts around the sprocket shaft and

the 3 bolts around the mainshaft on the

rear of the motorplate. Torque the bolts

28-32 ft. llbs.

NOTE: The 3 bolt holes in the rear of the

motorplate are machined to accomadate

both the transmission bolt circle pattern of

1990-2000 models as well as 2001-2006

models. You must determine which holes

apply for your model and then use the

proper bolt and flat washer. . (See figure

4, 4a & 4b).

Slide the motorplate into position for installation, making

sure that the crossover heel/toe shifter shaft is inserted

into the bung on the motorplate.

Figure 2

Figure 3

Figure 4

BRUTE IV 2” Touring Open

INSTALL ATION GUIDE

1 2 4 5 0 W H I T T I E R B L V D . , W H I T T I E R , C A 9 0 6 0 1

W W W . R I V E R A P R I M O I N C . C O M

2108-0025

Figure 1

Figure 4a

Figure 4b

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - INSTALL ATION GUIDE

NOTE: Read the instructions carefully before proceeding with the actual installation. NOTE: To avoid accidental start up of vehicle during the install

Seite 2

With the motorplate installed it is now time to move tothe right side of the motorcycle to re-install the starterto the rear of the motorplate. (See f

Seite 3

You are now ready to install the beltdrive on the shafts. To make it a littleeasier to slide the clutch basket ontothe mainshaft and the front pulleyo

Seite 4

Position the rear pulley on the very end of themainshaft splines and then wrap the belt on thefront & rear pulley and them together onto themotor

Seite 5

At this point if you removed the clutch pack from the rear pulley, you can now re-install the clutchpack into the clutch shell by inserting the .120”

Seite 6

The outer guard stand-offs have the studs pre-installed. (See figure 22) Should the need arise toremove the studs from the stand-offs, be sure to re-

Kommentare zu diesen Handbüchern

Keine Kommentare

Rivera-primo Brute IV 2" Touring Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio Rivera-primo Brute IV 2" Touring herunter. Rivera Primo Brute IV 2" Touring User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio Rivera-primo Brute IV 2" Touring